doc:appunti:hardware:tl-mr6400_openwrt
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
doc:appunti:hardware:tl-mr6400_openwrt [2023/02/01 16:26] – [The SNMP Daemon] niccolo | doc:appunti:hardware:tl-mr6400_openwrt [2023/10/31 15:17] – [Upgrade to OpenWRT 22.05.0] niccolo | ||
---|---|---|---|
Line 53: | Line 53: | ||
===== Upgrade the uqmi package ===== | ===== Upgrade the uqmi package ===== | ||
- | Download | + | Using the stock **uqmi** package provided by OpenWRT 22.03.2 I was not able to bring up the LTE interface. The error message shown by **logread** was: |
+ | |||
+ | < | ||
+ | daemon.notice netifd: lte4g (2329): Command failed: | ||
+ | ubus call network.interface notify_proto | ||
+ | { " | ||
+ | (Permission denied) | ||
+ | daemon.notice netifd: Interface ' | ||
+ | daemon.notice netifd: Interface ' | ||
+ | daemon.notice netifd: lte4g (2343): Waiting for SIM initialization | ||
+ | </ | ||
+ | |||
+ | I downloaded a custom **uqmi** packages for OpenWRT 22.03.2 here: **[[https:// | ||
The **uqmi** depends upon **libubox** and **libblobmsg-json**, | The **uqmi** depends upon **libubox** and **libblobmsg-json**, | ||
Line 61: | Line 73: | ||
^ libblobmsg-json20220515 | ^ libblobmsg-json20220515 | ||
+ | Now the '' | ||
+ | |||
+ | < | ||
+ | kern.info kernel: | ||
+ | kern.info kernel: | ||
+ | | ||
+ | | ||
+ | kern.info kernel: | ||
+ | kern.info kernel: | ||
+ | kern.info kernel: | ||
+ | daemon.notice netifd: Interface ' | ||
+ | daemon.notice netifd: lte4g (1900): PINcode disabled | ||
+ | daemon.notice netifd: lte4g (1900): Data format set to raw-ip | ||
+ | daemon.notice netifd: lte4g (1900): Default profile: 1 | ||
+ | daemon.notice netifd: lte4g (1900): Change default profile | ||
+ | daemon.notice netifd: lte4g (1900): | ||
+ | daemon.notice netifd: lte4g (1900): | ||
+ | daemon.notice netifd: lte4g (1900): Airplane mode off | ||
+ | daemon.notice netifd: lte4g (1900): | ||
+ | daemon.notice netifd: lte4g (1900): Registered to Iliad on LTE | ||
+ | daemon.notice netifd: lte4g (1900): Connected with IPv4 | ||
+ | daemon.notice netifd: lte4g (1900): Unable to connect with IPv6 | ||
+ | daemon.notice netifd: lte4g (1900): Setting up wwan0 | ||
+ | daemon.notice netifd: Interface ' | ||
+ | </ | ||
===== Configure the LTE connection ===== | ===== Configure the LTE connection ===== | ||
Line 264: | Line 301: | ||
</ | </ | ||
+ | ===== Wake-on-LAN ===== | ||
+ | |||
+ | I was not able to instal the **wakeonlan** package because it depends upon Perl (not enough space on flash memory). Fortunately I was able to install **etherwake**, | ||
+ | |||
+ | ===== Upgrade to OpenWRT 22.05.0 ===== | ||
+ | |||
+ | To upgrade from OpenWRT **22.03.3** to **22.05.0** we used the **sysupgrade** option, which preserves the existing configuration, | ||
+ | |||
+ | Download the new firmware **[[https:// | ||
+ | |||
+ | Once the router reboots, you can access it via SSH or LuCI web, the network configuration should have been preserved. | ||
+ | |||
+ | Beware that all the extra packages must be installed again, notably the **uqmi** package, required to drive the LTE modem for internet access, must be upgraded to version **[[https:// | ||
+ | |||
+ | The repository roots are: | ||
+ | |||
+ | * https:// | ||
+ | * https:// | ||
+ | |||
+ | This is the list of all the extra packages I installed (FIXME add the space required by each package): | ||
+ | |||
+ | ^ Packages installed and required space ^^ | ||
+ | ^ uqmi_2022-11-29-0.11_mipsel_24kc.ipk | ||
+ | ^ openvpn | ||
+ | ^ luci-app-openvpn | ||
+ | ^ tcpdump-mini | ||
+ | ^ snmpd | ||
+ | ^ luci-app-snmpd | ||
+ | ^ etherwake | ||
+ | ^ coreutils-base64 | ||
===== Web References ===== | ===== Web References ===== |
doc/appunti/hardware/tl-mr6400_openwrt.txt · Last modified: 2024/04/26 15:30 by niccolo