doc:appunti:hardware:mxq_s805
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
doc:appunti:hardware:mxq_s805 [2017/08/22 09:40] – [Which LibreELEC image to use?] niccolo | doc:appunti:hardware:mxq_s805 [2017/08/23 12:21] – [Android TV-Box MXQ (Amlogic S805)] niccolo | ||
---|---|---|---|
Line 11: | Line 11: | ||
^ CPU | ARMv7 revision 1 | ARMv7 revision 1 | | ^ CPU | ARMv7 revision 1 | ARMv7 revision 1 | | ||
^ Machine | ^ Machine | ||
- | ^ Total RAM memory | + | ^ Total RAM memory |
^ NAND Storage | ^ NAND Storage | ||
^ WiFi driver | ^ WiFi driver | ||
Line 20: | Line 20: | ||
The device does not have a clock inside, it relies on the time it gets from the internet. With the latest firmware (2016-01-26) there is a **very annoying bug**: from the Android settings we enabled **time from the internet** and set the proper timezone, this settings works just once, after a reboot the time is **almost always unset**. | The device does not have a clock inside, it relies on the time it gets from the internet. With the latest firmware (2016-01-26) there is a **very annoying bug**: from the Android settings we enabled **time from the internet** and set the proper timezone, this settings works just once, after a reboot the time is **almost always unset**. | ||
+ | |||
+ | ===== Video Resolution ===== | ||
+ | |||
+ | We don't know the actual **video adapter capabilities** of the MXQ, using the LibreELEC distribution we suspect that it cannot cope well with the native resolution of any HDMI monitor we connect to it. For example we attached a Samsung SyncMaster capable of 1440x900 pixel, but the Kodi interface offered only **1920x1080**, | ||
+ | |||
===== Partitions and storage space ===== | ===== Partitions and storage space ===== | ||
Line 170: | Line 175: | ||
The Linux partition is empty, **it will be resized** to occupy the entire space available on the SD card and it will contain runtime data for LibreELEC. | The Linux partition is empty, **it will be resized** to occupy the entire space available on the SD card and it will contain runtime data for LibreELEC. | ||
- | Once prepared the SD card, insert it into the powered-off | + | Once you prepared the SD card, insert it into the unpowered |
You will need an **USB keyboard** to configure the Kodi program (the remote control should work, but it is not very friendly selecting IP addresses, etc.). At least you should **configure the network** and **enable the SSH server**. | You will need an **USB keyboard** to configure the Kodi program (the remote control should work, but it is not very friendly selecting IP addresses, etc.). At least you should **configure the network** and **enable the SSH server**. | ||
Line 191: | Line 196: | ||
... | ... | ||
</ | </ | ||
+ | |||
+ | ==== Solved and Unsolved Problems ==== | ||
+ | |||
+ | === LibreELEC-S805.arm-8.2-8.1.5a-m201d === | ||
+ | |||
+ | The **power button of the remote control** does power off the device, but it is unable to wake it up. You must disconnect the power supply and connect it again. | ||
+ | |||
+ | Sometimes we get **Kodi reboot**, Kodi interface or **video play freeze**. The system is installed into the NAND memory, into the dmesg log there are plenty of that messages: | ||
+ | |||
+ | < | ||
+ | nftl _nand_discard, | ||
+ | nftl _nand_discard, | ||
+ | nftl _nand_discard, | ||
+ | </ | ||
+ | |||
+ | The Kodi program crashes with the following message: | ||
+ | |||
+ | < | ||
+ | Program terminated with signal SIGBUS, Bus error. | ||
+ | </ | ||
+ | |||
+ | May be there are problems with NAND memory? FIXME Must investigate running the same releas from SD card and/or running a different release from NAND. | ||
+ | |||
+ | === LibreELEC-S805.arm-8.2-8.1.5-HD18Q === | ||
+ | |||
+ | The **volume buttons of the remote control** do not work. You can instead press OK when playing a vide, then use the gear icon to access the menu. | ||
+ | |||
+ | === LibreELEC-S805.m201d.arm-7.0.3.3d.img === | ||
+ | |||
+ | We disabled **[[wp> | ||
+ | |||
+ | < | ||
+ | ##### cec write error! ##### | ||
+ | </ | ||
+ | |||
+ | Go to //System// --> //System// --> //Input devices// --> // | ||
====== TWRP Backup images ====== | ====== TWRP Backup images ====== | ||
Line 210: | Line 251: | ||
* [[http:// | * [[http:// | ||
- | * [[http://freaktab.com/forum/tv-player-support/amlogic-based-tv-players/23766-rom-unofficial-openelec-for-mk808b-and-mxq|Unofficial OpenELEC for MK808B+ and MXQ]], points to LibreELEC indeed, this OpenELEC port is not longer updated. | + | * [[http://www.microdev.it/wp/it/2016/12/ |
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// |
doc/appunti/hardware/mxq_s805.txt · Last modified: 2020/01/27 12:01 by niccolo