doc:appunti:android:osmand_on_motorbike
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
doc:appunti:android:osmand_on_motorbike [2022/08/09 15:29] – [Mounting] niccolo | doc:appunti:android:osmand_on_motorbike [2023/09/04 09:34] – [Using OsmAnd on a motorbike] niccolo | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Using OsmAnd on a motorbike ====== | ====== Using OsmAnd on a motorbike ====== | ||
- | In this article I write some notes about using and **Android** device (actually a **smartphone**) as a **GPS navigation system on a motorbike**. The choosen software is **[[https:// | + | In this article I write some notes about using and **Android** device (actually a **smartphone**) as a **GPS navigation system on a motorbike**. The choosen software is **[[https:// |
===== Mounting ===== | ===== Mounting ===== | ||
Line 7: | Line 8: | ||
First of all, it is necessary to make a premise: I usually travel at very low speeds, hardly exceeding **90 km/h**. My bike, despite being a **650 cc twin cylinder**, has few vibrations and I only occasionally drive on dirt roads. Here I tell you what is my setup, which is working well for my needs, but you must adapt the mounting to your specific scenario. | First of all, it is necessary to make a premise: I usually travel at very low speeds, hardly exceeding **90 km/h**. My bike, despite being a **650 cc twin cylinder**, has few vibrations and I only occasionally drive on dirt roads. Here I tell you what is my setup, which is working well for my needs, but you must adapt the mounting to your specific scenario. | ||
- | I provided both the smartphones with a **flexible TPU cover**. The ZTE is quite thin, so it is blocked firmly by the holder. | + | I provided both the smartphones with a **flexible TPU cover**. The ZTE is quite **thin**, so it is blocked firmly by the holder |
+ | |||
+ | FIXME | ||
===== Waterproof ===== | ===== Waterproof ===== | ||
Line 14: | Line 17: | ||
Instead the **WP12** is rated as **[[wp> | Instead the **WP12** is rated as **[[wp> | ||
- | {{.: | + | {{.: |
Line 25: | Line 28: | ||
To keep the ZTE permanently connected to the **charging cable**, I purchased a **micro-USB magnetic adapter** (specifically a **NetDot 10th Gen**). The magnetic adapter is quite convenient to plug/unplug the power connector even wearing gloves and it prevents damages if you inadvertently pull the cable. | To keep the ZTE permanently connected to the **charging cable**, I purchased a **micro-USB magnetic adapter** (specifically a **NetDot 10th Gen**). The magnetic adapter is quite convenient to plug/unplug the power connector even wearing gloves and it prevents damages if you inadvertently pull the cable. | ||
- | {{.: | + | {{.: |
In the photo above you can see two adapters: one fitted into the phone connector and the one that I carry with me as a **spare part**. I used just a bit of silicone adhesive to make the plug more stable and to prevent dust from entering. It turned out that the magnetic coupling is quite **strong and stable** to resist to vibrations and wind. You must pay attention to avoid dust into the electric contacts, which are rather delicate and can actract **ferromagnetic dust**. | In the photo above you can see two adapters: one fitted into the phone connector and the one that I carry with me as a **spare part**. I used just a bit of silicone adhesive to make the plug more stable and to prevent dust from entering. It turned out that the magnetic coupling is quite **strong and stable** to resist to vibrations and wind. You must pay attention to avoid dust into the electric contacts, which are rather delicate and can actract **ferromagnetic dust**. | ||
Line 36: | Line 39: | ||
===== Overheating ===== | ===== Overheating ===== | ||
+ | |||
+ | ===== OsmAnd settings ===== | ||
doc/appunti/android/osmand_on_motorbike.txt · Last modified: 2023/09/04 09:42 by niccolo